Aaron Merke- Neill Gorton 3d Ol age Home work

Aaron Merke · February 2015

Hey Niell,

This is what I have so far. Fortunately I have been working so Unable to join you in class. It has also left me to complete this in two days. here is what I have so far. hopefully, I will be done by Midnight.
we will see. currently waiting on 4 hour cure silicon. it was the closest to 25silicon I had.

Here it is:

Image: https://us.v-cdn.net/5020761/uploads/editor/5i/r8c9iqagszgr.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/w1/wr6cgxlvuxju.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/a2/50w79ul3dq79.jpg

Aaron Merke · February 2015

Second. set. cutting edge, Molding setup, and first mold. done with dragon skin. a lil quicker:)

Image: https://us.v-cdn.net/5020761/uploads/editor/f1/9va991amqbjs.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/uy/pdr7bf0n9t7o.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/wy/dd6z12pqikt3.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/a5/5jlawta46j8f.jpg

Aaron Merke · February 2015

Here is where I am currently. Molding the bigger layer. while waiting I sculpted my own appliances.
hope I get them on the model by 12 tonight. We will see.

thanks again.

Image: https://us.v-cdn.net/5020761/uploads/editor/s0/o6m352fjkezc.jpg

Aaron Merke · February 2015

The New sculpt. Extra set for myself.

Image: https://us.v-cdn.net/5020761/uploads/editor/o2/3vwex2x450v1.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/oh/xevlx9cv5imw.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/ze/nzq2y6l790f9.jpg

Aaron Merke · February 2015

Well its not setting up quickly due to us being in a Canadian basement. Will try first thing tomorrow morn.

Sue Lee · February 2015

Good luck! The sculpts look good and the molding looks clean. I like how half of us are using FX Pro. I didn't deaden mine 100% but for the next run I would rather do 100%.

Aaron Merke · February 2015

Thanks. I should have used FX pro for the block mold. lesons learnt. read cureing time always!!!!! ha:)

Rosanna Wells · February 2015

I had the same problem with my curing time... I accidentally bought one that was 24 hours to cure! I used Plaster instead.

Good work!

Aaron Merke · February 2015

Here is the Mold ready to be applied. ( made the mistake of not pushing hard enough made my edges too thick. and annoying to work with.

Image: https://us.v-cdn.net/5020761/uploads/editor/fz/i29j5jo86xc5.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/so/y6kwonw4l0tf.jpg

Aaron Merke · February 2015

Here is Lauren, my sick

Image: https://us.v-cdn.net/5020761/uploads/editor/b4/mhfisjhi8dez.jpg

Aaron Merke · February 2015

Don't know why they the site re positions my photos. Here is final application:

I had bad edges due to not pushing down hard enough on mold. attempted to fixed half of application with pro aide. I tad frustrating. I only did full application to half of the face because we were running out of time. hope that's OK.

Also the painting and matching of skin to me was a little off. I am doing this application again on Friday for a photo so we will see. any recommendations would be valued.

Image: https://us.v-cdn.net/5020761/uploads/editor/vt/fd4dbzucof9z.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/7z/a21k5hpqdlgg.jpg

Image: https://us.v-cdn.net/5020761/uploads/editor/nc/u6cnodegyu6j.jpg

Aaron Merke · February 2015

Here is the second application. I think the Bald cap plastic may have been a little heavy. I am getting closer I think to nicer edges. I am proud of the secound round of the colour match. Just have to get the edges figured out.

Aaron Merke- Neill Gorton 3d Ol age Home work

Comments